[C38] between dinette seat and holding tank

[Ray Torok]

The idea was to look at cutting the cabin sole (not the mast) to get better
access to the bottom of the mast and the step.  I'm not sure how much it
would help.  The idea of additional holes in the mast is another question.


On Mon, Jun 24, 2013 at 3:55 PM, Donald Strong <drstrong at ucdavis.edu> wrote:

>  Don't hole that mast!
>
> On 6/24/13 3:39 PM, Ray Torok wrote:
>
> Argh!  Isn't this why they invented saber saws?
>
>
> On Mon, Jun 24, 2013 at 3:35 PM, littlebreeze at comcast.net <
> littlebreeze at comcast.net> wrote:
>
>> Shit
>>
>>
>> Sent from the San Francisco Bay, home of the 2013 Catalina 38 Nationals.
>>
>>
>>  ----- Reply message -----
>> From: "Max Soto" <maxsoto at gmail.com>
>> To: "Catalina 38 Listserve" <listserve at catalina38.org>
>> Subject: [C38] Wiring the Mast
>>  Date: Mon, Jun 24, 2013 15:17
>>
>>
>> Exactly, in that tiny space between the holding tank and the fiberglass..
>>
>> Max Soto
>> +506-8312-1367
>> Alajuela, Costa Rica
>>
>> On 24/06/2013, at 16:07, "littlebreeze at comcast.net" <
>> littlebreeze at comcast.net> wrote:
>>
>>  So to clarify, most are using the existing hole(s) on the dinette side
>> of the mast.  I mean in that tiny space between the mast and the holding
>> tank.   No one is adding a hole on the companion way side of the mast, for
>> access, and then putting a cover over the hole after the wires are run?
>>
>> Kerry
>>
>> Sent from the San Francisco Bay, home of the 2013 Catalina 38 Nationals.
>>
>>
>> ----- Reply message -----
>> From: "Steve Smolinske" <SSmolinske at rainierrubber.com>
>> To: "Catalina 38 Listserve" <listserve at catalina38.org>
>> Subject: [C38] Wiring the Mast
>> Date: Mon, Jun 24, 2013 13:53
>>
>>
>>  That should work if there is enough room in the conduit and the wires
>> are not wrapped all around each other, if you try make sure to really tape
>> the messenger and the wires together very good.
>>
>>
>>
>> *From:* listserve-bounces at catalina38.org [
>> mailto:listserve-bounces at catalina38.org<listserve-bounces at catalina38.org>]
>> *On Behalf Of *littlebreeze at comcast.net
>> *Sent:* Monday, June 24, 2013 12:37 PM
>> *To:* Catalina 38 Listserve
>> *Subject:* Re: [C38] Wiring the Mast
>>
>>
>>
>> No I didn't.  I'm learning more and more as I go along.  But I'm
>> wondering if I can use one of the existing wires as a messenger?
>>
>> Kerry
>>
>> Sent from the San Francisco Bay, home of the 2013 Catalina 38 Nationals.
>>
>>  ----- Reply message -----
>> From: "Steve Smolinske" <SSmolinske at rainierrubber.com>
>> To: "Catalina 38 Listserve" <listserve at catalina38.org>
>> Subject: [C38] Wiring the Mast
>> Date: Mon, Jun 24, 2013 09:11
>>
>>
>>
>> Kerry, did they leave a messenger in your conduit when they rewired the
>> mast?
>>
>>
>>
>> *From:* listserve-bounces at catalina38.org [
>> mailto:listserve-bounces at catalina38.org<listserve-bounces at catalina38.org>]
>> *On Behalf Of *littlebreeze at comcast.net
>> *Sent:* Monday, June 17, 2013 9:43 AM
>> *To:* Catalina 38 Listserve
>> *Subject:* Re: [C38] Wiring the Mast
>>
>>
>>
>> If it was 30 year old wiring in the mast I wouldn't even ask the
>> question.  The mast wiring is only six years old and was changed when the
>> mast was pulled for painting.  But its still a valid answer.
>>
>> Kerry
>>
>> Sent from the San Francisco Bay, home of the 2013 Catalina 38 Nationals.
>>
>> ----- Reply message -----
>> From: "cat38skip" <cat38skip at yahoo.com>
>> To: <listserve at catalina38.org>
>> Subject: [C38] Wiring the Mast
>> Date: Mon, Jun 17, 2013 06:06
>>
>>
>>
>> Kerry,
>>
>> We re-wired the entire mast, in place, last year, New masthead light and
>> wires new steaming/deck light and wire, new VHF cable and antenna and
>> re-strung the masthead wind transducer. We have a 1 1/2 inch hole near the
>> bottom of the mast at cabin sole level. It was easy :-) . That is,  after
>> the hard, frustrating hours and days of mistakes & re-re-re-pulling of the
>> tangled wires and messenger strings. Once we sorted out the best messenger
>> to use (weed eater 'string') it was a matter of having someone up top who
>> was comfortable being there AND who knew what he was doing, 2-way
>> communication and staging the sequence and materials. We replaced all the
>> bulbs with LED's so the wire guage was reduced significantly. We used
>> multi-wire cable to reduce tangles. The PO had installed all primary wire
>> and it was a mess.
>>
>> Give me a call or we can get together ..
>>
>> Do you have someone to go uo there for you?
>>
>>
>>
>> Dave
>>
>>
>>
>>
>> Sent from South San Francisco, where the wind never stops.
>>
>>
>> littlebreeze at comcast.net wrote:
>>
>> Happy Fathers Day to the group.
>>
>> I was thinking of installing a wind speed indicator at the top of the
>> mast.  However when I looked into accessing the existing wiring and PVC
>> conduit, it looks to be an impossible task without pulling the mast.  Has
>> anyone overcome this issue without pulling the mast?  The only way I can
>> come up with is to cut a 3.5 inch hole in the starboard side of the mast
>> approximately 6" from the bottom of the mast, and then, after making the
>> appropriate connections, affix  a cover plate to the access hole.  Will
>> this weaken the mast beyond use?  Should I just pull the mast?
>>
>> Kerry Grimes
>> Little Breeze 139
>> San Francisco
>>  ------------------------------
>>
>> No virus found in this message.
>> Checked by AVG - www.avg.com
>> Version: 10.0.1432 / Virus Database: 3199/5936 - Release Date: 06/24/13
>>  ------------------------------
>>
>> No virus found in this message.
>> Checked by AVG - www.avg.com
>> Version: 10.0.1432 / Virus Database: 3199/5936 - Release Date: 06/24/13
>>
>>  _______________________________________________
>> Listserve mailing list
>> Listserve at catalina38.org
>> http://catalina38.org/mailman/listinfo/listserve_catalina38.org
>>
>>
>> _______________________________________________
>> Listserve mailing list
>> Listserve at catalina38.org
>> http://catalina38.org/mailman/listinfo/listserve_catalina38.org
>>
>>
>
>
> _______________________________________________
> Listserve mailing listListserve at catalina38.orghttp://catalina38.org/mailman/listinfo/listserve_catalina38.org
>
>
>
> _______________________________________________
> Listserve mailing list
> Listserve at catalina38.org
> http://catalina38.org/mailman/listinfo/listserve_catalina38.org
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://catalina38.org/pipermail/listserve_catalina38.org/attachments/20130624/3e1d1d15/attachment-0001.htm>