[C38] mainsheet traveler.

[Joseph Launie]

Bob,
    They are sitting in my workshop. I replaced them with Harken Risers 
which came with the new track. Joe

Robert Miller wrote:
>
> Now that the blocks are off, maybe you should do as I did.  Take them 
> home and do a really nice varnish job on them.
>
>  
>
> Bob
>
>  
>
> *From:* listserve-bounces at catalina38.org 
> [mailto:listserve-bounces at catalina38.org] *On Behalf Of *Joseph Launie
> *Sent:* Sunday, April 11, 2010 7:09 PM
> *To:* Catalina 38 Listserve
> *Subject:* Re: [C38] mainsheet traveler.
>
>  
>
> Paul,
>     We were able to get the blocks off much easier than we feared. 
> They were just held on by 3 -  8 inch long 1/4 inch bolts each. We 
> used  the direct approach of unbolting the nuts below decks and 
> banging on he bottom of the bolts with a hammer. We found that the 
> blocks were only on the  deck with bedding compound. Joe
>
> PAUL NOTTE wrote:
>
> You guys are frightening me I was going to remove the blocks under the 
> traveler to refinish them.
>
>   Anyway Max you said you waxed your boat every three months or so , 
> any suggestions on wax for the northwest and application proceedures??
>
> ----- Original Message -----
> From: Steve Smolinske <SSmolinske at rainierrubber.com> 
> <mailto:SSmolinske at rainierrubber.com>
> Date: Friday, April 9, 2010 10:21 pm
> Subject: Re: [C38] mainsheet traveler.
> To: Catalina 38 Listserve <listserve at catalina38.org> 
> <mailto:listserve at catalina38.org>
>
> > liguid wrench sprayed in overnight for a few days and then heat
> > to the track, slight tapping and wiggling with vice grips should
> > do the trick. 
> >
> > ________________________________
> >
> > From: listserve-bounces at catalina38.org 
> <mailto:listserve-bounces at catalina38.org> on behalf of Kenneth M. Sutto
> > Sent: Fri 4/9/2010 1:55 PM
> > To: Organization - listserve at catalina38
> > Subject: [C38] mainsheet traveler.
> >
> >
> > Here's my problem. The pully wheels on my traveler cars are
> > broken. There are two on each car and are stacked one on top of
> > the other. At the end of the traveler track on each side is a
> > stainless pin through the track stopping the car from going off.
> > On top of the pin and end of the track is a hard rubber cap
> > which I pried off. I cannot remove the pins to get the cars off.
> > I have tried just about everything I know. I am thinking of
> > using heat on the pin then tapping them out with vice grips and
> > a hammer. Any suggestions?
> > I would send photos but something is wrong with my computer.
> >
> >
> > Help!!
> >         Ken
> > Sutto          "Sundancer"
> >
> >
> > ________________________________
> >
> > The New Busy is not the too busy. Combine all your e-mail
> > accounts with Hotmail. Get busy.
> > 
> <http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4> 
> <http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4>  
>
> >
>
>  
> ------------------------------------------------------------------------
>
>
>   
>  
> _______________________________________________
> Listserve mailing list
> Listserve at catalina38.org <mailto:Listserve at catalina38.org>
> http://catalina38.org/mailman/listinfo/listserve_catalina38.org
>   
> ------------------------------------------------------------------------
>
> _______________________________________________
> Listserve mailing list
> Listserve at catalina38.org
> http://catalina38.org/mailman/listinfo/listserve_catalina38.org
>   
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://catalina38.org/pipermail/listserve_catalina38.org/attachments/20100411/d5619e66/attachment-0001.htm>