[C38] FW: 8/6/2011 1300 PDT Hassle update

Tue Aug 9 12:58:51 EDT 2011

At least the starter was not destroyed and they were able to start the
engine...  Weird that they are having the overheat problem on the electrical
system, but at least they can charge batteries and make water.....

Max

2011/8/9 tdtron at earthlink.net <tdtron at earthlink.net>

>  *Wow!  I have never heard of a starter armature not coming apart when the
> starter Bendix didn't disengage.  The low RPM's of our engines has probably
> saved the day because in a higher RPM car that starter wouldn't be fit even
> for a core exchange.*
> **
> *This is truly good news, even if they are now experiencing overcharging
> from that "generator" starter.  Hopefully the starter and ring gear will
> hold up long enough to get them home.  *
> **
> *As a side note, if Larry does end up having to replace the ring gear
> after he gets home, it will be a good time to get rid of the steel flex
> plate on the flywheel and replace it with a PYI synthetic flex plate.  The
> original flex plates on our boats tend to fatigue the springs over time and
> when the springs do break apart, there is no positive contact left to turn
> the transmission.   The engine just feels like it is in neutral and those
> little pieces of springs just go around and around making a mess of the bell
> housing.  I know, it has happened to me and others I have spoken to.  The
> PYI flex plate has positive engagement even if the synthetic damping
> material fails so you keep on going regardless.  I also replaced my
> Universal shaft coupling with a PYI synthetic coupling at the same time and
> the engine became much smoother at all speeds.  It was like adding more
> cylinders to the engine, there was no comparison to the original
> components.  I can't say which of the two components made the most
> improvement but as a pair, the results were nothing short of wonderful.*
> **
> *Keep us posted on Larry, thanks.*
> **
> *Tom Troncalli*
>
>
>
> ----- Original Message -----
> *From:* Steve Smolinske <SSmolinske at rainierrubber.com>
> *To: *Catalina 38 Listserve <listserve at catalina38.org>
> *Sent:* 8/9/2011 7:51:54 AM
> *Subject:* [C38] FW: 8/6/2011 1300 PDT Hassle update
>
>  Passing along an update from Team Hassle.  I passed along the suggestion
> to jump the solenoid not sure if that is what got their motor going or not
> but the next day they got it started, as you can see below its not an ideal
> situation but at least they have the ability to recharge and make additional
> water.
>
> Steve
> #312 Peregrine
> Seattle
>
>
>  Hi All
> He is David's Email for today.
> Keep the Faith
>
> Tamara J. Summers
>
>  ------------------------------
>
> Hassle called at 1300 PDT and I spoke to Larry.
>
>
>
>    - Their current position is 35 38.9N 149 25.5W. This is east of where
>    we advised that they head yesterday. Please see the map below.
>    - They covered almost 90 miles yesterday in variable winds
>    - The wind is currently about 10 knots from the east and they are
>    making around 6 knots on a course of 000. I advised them to head north on a
>    course of 345 and to fall off to the west if possible. I told them that they
>    would need to be up around 42-44 before they would see the westerly winds.
>    - They are now able to start the engine; however the electrical system
>    quickly overheats, apparently from excessive charging. They suspect that the
>    starter motor is still engaged and acting as a generator. Since they have
>    bypassed the fuses, this is a dangerous situation and they can only run the
>    engine for around 20 minutes at a time.
>    - They are making water, using each of the house batteries
>    sequentially. A battery at full charge is able to produce about four gallons
>    of water.
>    - They have been fishing and so far have caught 2 Dorado.
>
>
>
>
>
> Other items:
>
>
>
>    - Next to each of the parts, I’ve indicated the person who volunteered
>    to get them. We still need volunteers for the start switch and the fuel
>    separator filters.
>    - Adrian and Larry will stay aboard the boat and bring it to Long
>    Beach. Caleb and John will probably get of at Moss Landing. So there are 2 –
>    4 slots available for the return crew.
>
>
>
> Parts required:
>
>
>
>    - DK - 4 – ANL 150 fuses
>    - JM - 1 - Starter motor part number is #200948 the engine is a
>    Westerbeke Universal B M-25XPB. (Kubota)
>    - 1 – Push button start switch
>    - DJ - 2 – Auto float switches for the bilge pump
>    - DK - 1 – Package 10-12 gauge butt connectors
>    - 2 – Fuel separator filters
>
>
>
>
>
>
>
>
>
> Notes:
>
>
>
> ?         The red track is Expedition’s proposed track to route them
> around the high.
>
> ?         The wind barbs are as of this afternoon. Although the route
> appears to be directly through the high, there will be significant changes
> in the location of the high over the next few days.
>
> ?         The marks with dates reflect Hassle’s actual location on that
> date.
>
> ?         The computer estimate of time to Moss Landing is around 14 days.
>
>
>
> David Kraai
>
> President
>
>
>
>
>
>
> _______________________________________________
> Listserve mailing list
> Listserve at catalina38.org
> http://catalina38.org/mailman/listinfo/listserve_catalina38.org
>
>

-- 
Max Soto
C38 #198 ESTANCIA
Puntarenas, Costa Rica
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://catalina38.org/pipermail/listserve_catalina38.org/attachments/20110809/28ae4f20/attachment-0001.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 67795 bytes
Desc: not available
URL: <http://catalina38.org/pipermail/listserve_catalina38.org/attachments/20110809/28ae4f20/attachment-0001.jpg>