[C38] Emergency tiller

Fri Oct 24 17:44:15 EDT 2008

On Legacy, hull #360, the emergency tiller goes in a round socket at the top
of the rudder shaft.  We just have a short piece of pipe as an emergency
tiller but it's really too short to steer by hand as it has to clear the
wheel pedestal.  I thought about welding up one with a big jog in the middle
to clear the pedestal. 

Rich, Legacy, #360, Los Angeles Harbor

  _____  

From: listserve-bounces at catalina38.org
[mailto:listserve-bounces at catalina38.org] On Behalf Of Max Soto
Sent: Thursday, October 23, 2008 10:43 AM
To: Catalina 38 Listserve; TherORl at aol.com
Subject: [C38] Emergency tiller

Hi Mike,

You can make your own emergency tiller. It is very simple. Some wood, couple
of stainless steel plates, three bolts, and that`s all it take to make one.
Attached is the diagram from Catalina.
Hope this helps.

Regards
Max Soto
 C38 #198 ESTANCIA 
Puntarenas, Costa Rica 

2008/10/23, TherORl at aol.com <TherORl at aol.com>: 

I have a 1984 Catalina38. My wife and I bought her about five years ago.
We've done some sailing outside the gate but it's a little scary when you
don't have an emergency tiller. 

Where would you acquire such a thing. Also, I am in dire need of new sails
and with money a little tight where would I get a set of used but good sails
for sailing San Francisco Bay.

Mike O'Reilly
Lucky Star 

In a message dated 10/23/2008 9:00:31 A.M. Pacific Daylight Time,
listserve-request at catalina38.org writes:

Send Listserve mailing list submissions to
    listserve at catalina38.org

To subscribe or unsubscribe via the World Wide Web, visit
    http://catalina38.org/mailman/listinfo/listserve_catalina38.org
or, via email, send a message with subject or body 'help' to
    listserve-request at catalina38.org

You can reach the person managing the list at
    listserve-owner at catalina38.org

When replying, please edit your Subject line so it is more specific
than "Re: Contents of Listserve digest..."

Today's Topics:

   1. Re: Dome Lights (Steve Smolinske)
   2. seperating the coupling (bob gouley)
   3. Re: seperating the coupling (Larry Malmberg)

----------------------------------------------------------------------

Message: 1
Date: Wed, 22 Oct 2008 23:29:16 -0700
From: Steve Smolinske <SSmolinske at rainierrubber.com>
Subject: Re: [C38] Dome Lights
To: Catalina 38 Listserve <listserve at catalina38.org>
Message-ID: <71DD90DC-B678-4E31-8078-E8068937E802 at mimectl>
Content-Type: text/plain; charset="us-ascii"

An HTML attachment was scrubbed...
URL:
<http://catalina38.org/pipermail/listserve_catalina38.org/attachments/200810
22/74566572/attachment-0001.html>

------------------------------

Message: 2
Date: Thu, 23 Oct 2008 09:36:43 -0400
From: "bob gouley" <r.gouley at sympatico.ca>
Subject: [C38] seperating the coupling
To: <listserve at catalina38.org>
Message-ID: <BLU0-SMTP6C01BB0783913F37467BCE0280 at phx.gbl>
Content-Type: text/plain; charset="iso-8859-1"

     I would like to sepaerate the coupling on my engine 5424 type, It is
held together by four bolts that I removed but the coupler will not come
apart. I am worried about damage if I force it apart.  The coupler has
llarge bolts with rubber washers on the circumference, I don`t think these
are to be removed?  Currently I am soaking the shaft set screws with
penetrating oil, as I can`t budge them, next is to seperate the coupler, any
advice would be greatly appreciated. bob

Zephyr # 142
ST Joes Island 
Ontario Canada
r.gouley at sympatico.ca 
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://catalina38.org/pipermail/listserve_catalina38.org/attachments/200810
23/74d00dea/attachment-0001.html>

------------------------------

Message: 3
Date: Thu, 23 Oct 2008 08:54:08 -0700
From: "Larry Malmberg" <larrypi at linkline.com>
Subject: Re: [C38] seperating the coupling
To: "'bob gouley'" <r.gouley at sympatico.ca>,    "'Catalina 38 Listserve'"
    <listserve at catalina38.org>
Message-ID: <70FD97F8F31844DFAB2B4C5BD1B54790 at lmi.local>
Content-Type: text/plain; charset="us-ascii"

Bob, seems like the shipyard had to heat the bolts on our coupling and then
cut them off, I don't know if they used a torch to cut them but I do know
they had a heck of a time getting them off. 

Best regards,

Larry Malmberg-President

Larry Malmberg Investigations and Security, Inc.
505 North Arrowhead Avenue - Suite 510
San Bernardino, CA 92401-1200
909-383-8565, 800-655-4549 Facsimile 909-383-8566
PI 15211, PPO 112446

www.larrypi.com <http://www.larrypi.com/> 

All incoming and outgoing e mail is scanned with Norton AntiVirus.

Civil and Criminal, Surveillance, Internal Investigations, Personal and
Personnel Protection, GPS Tracking and Rental, Notary.

"The American Indians found out what happens when  you don't control
immigration"

"Life is not a journey to the grave with the intention of arriving safely in
a pretty and well preserved body, but rather to skid in broadside,
thoroughly used up, totally worn out, and loudly proclaiming; WOW-- What a
Ride!"

CONFIDENTIALITY NOTICE: This electronic message, including any attachments,
is for the sole use of the intended recipient(s) and may contain
confidential and privileged information. Any unauthorized review, copying,
use, disclosure or distribution of any parts of the contents of this
message/information is prohibited by federal law. Attempts to intercept this
message are in violation of Title 18 USC 2511(1) of the Electronic
Communications Privacy Act (ECPA), which subjects the interceptor to fines,
imprisonment and/or civil damages. If you are not the intended recipient,
please contact the sender by reply e-mail and destroy all copies of the
original message.

  _____  

From: listserve-bounces at catalina38.org
[mailto:listserve-bounces at catalina38.org] On Behalf Of bob gouley
Sent: Thursday, October 23, 2008 6:37 AM
To: listserve at catalina38.org
Subject: [C38] seperating the coupling

     I would like to sepaerate the coupling on my engine 5424 type, It is
held together by four bolts that I removed but the coupler will not come
apart. I am worried about damage if I force it apart.  The coupler has
llarge bolts with rubber washers on the circumference, I don`t think these
are to be removed?  Currently I am soaking the shaft set screws with
penetrating oil, as I can`t budge them, next is to seperate the coupler, any
advice would be greatly appreciated. bob

Zephyr # 142

ST Joes Island 

Ontario Canada

r.gouley at sympatico.ca 

-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://catalina38.org/pipermail/listserve_catalina38.org/attachments/200810
23/379296c0/attachment-0001.html>

------------------------------

_______________________________________________
Listserve mailing list
Listserve at catalina38.org
http://catalina38.org/mailman/listinfo/listserve_catalina38.org

End of Listserve Digest, Vol 4, Issue 303
*****************************************

  _____  

Play online games for FREE at Games.com! All of your favorites, no
registration required and great graphics - check it
<http://pr.atwola.com/promoclk/100000075x1211202682x1200689022/aol?redir=%0A
http://www.games.com?ncid=emlcntusgame00000001> out!

_______________________________________________
Listserve mailing list
Listserve at catalina38.org
http://catalina38.org/mailman/listinfo/listserve_catalina38.org

-- 
Max Soto C38 #198 ESTANCIA Puntarenas, Costa Rica 

Checked by AVG - http://www.avg.com
Version: 8.0.175 / Virus Database: 270.8.2/1741 - Release Date: 10/24/2008
8:33 AM

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://catalina38.org/pipermail/listserve_catalina38.org/attachments/20081024/95f18063/attachment-0001.htm>